44/62 Ultra Plus Laminator User manual Manuel de l’utilisateur Betriebsanleitung Manual de uso Manuale d’uso 7001507
8 Unpacking and Installation 3 UNPACKING AND INSTALLATION Please read and fully understand the entire manual before proceeding to use your laminator
Unpacking and Installation 9 English 3.5 Setting up the laminator in 4 steps. 1. Remove the cardboard box and the plastic bag as described on the
10 Unpacking and Installation 5. Finally, mount the middle part between the LH- and RH parts. Use two serrated washers and two socket screws M6x16.
Unpacking and Installation 11 English Your 44/62 Ultra Plus must be setup at the place where it will be used. The stand must be placed on a flat lev
12 Unit description 4 UNIT DESCRIPTION Features and benefits of the 44/62 Ultra Plus: Figure 7 Identification of parts 1 Wind-up tube Wind-up fo
Unit description 13 English 4.1 Control panel Figure 8 4.2 Motor control The speed of the rollers is continuously adjustable between 0 and 2.13m
14 Unit description 4.2.1 Slow-mode The machine has a slow-mode, which can be activated by pressing the foot switch. To maintain slow-mode, keep th
Unit description 15 English 4.3 Unwind brakes Tighten the supply brake so that it applies sufficient tension to laminate. Turning the knurled colla
5 PROCESS CONTROL SHEET Pressure Sensitive Thermal Application Unwind Recommended SEAL products Speed Unwind Recommended SEAL products Speed T
Application Processes 17 English 6 APPLICATION PROCESSES 6.1 Loading the machine The following steps outline the basic procedure that have to be u
English All rights reserved All information included in this manual as well as information included in supplements or addendum to this manual is subj
18 Application Processes Figure 12 6.1.2 Loading film onto a machine equipped with the cam lock system. • Remove the desired supply shaft (top or
Application Processes 19 English 6.2 Webbing the films After the laminator has heated up; • Remove the infeed table. If applicable, the infeed ta
20 Application Processes Figure 17 Alternative way for webbing film on the bottom unwind. • Use the provided leaderboard to push the film(s) t
Application Processes 21 English 6.3 Feeding images To aid feeding images, the laminator is provided with an “Image Guide”. This device can be posi
22 Application Processes 6.4 Laminating and adhesive coating (Decaling) This process involves sandwiching an image between either a hot or cold la
Application Processes 23 English 6.5 Decaling without liner Preparation: Select the films that you will use on the top and bottom of the images, i
24 Application Processes 6.6 Mounting This process involves mounting down previously prepared decals onto a substrate. No films or adhesives are us
Application Processes 25 English 6.7 Encapsulating This process involves completely sealing an image between two heat-activated films. Once the mac
26 Application Processes 6.8 Pre-Coating This process is used to coat substrates with a self-adhesive coating onto which images can be mounted. The
Application Processes 27 English 6.10 Mounting and Lamination using a ProSEAL®pouch Board. 1. Refer to the instruction sheet packed with each box o
English Français Deutsch Español Italiano 44/62 Ultra Plus Laminator User manual 7001708, Rev.A July 2007
28 Application Processes 6.11 Encapsulating with a ProSEAL® Flexible Pouch using a ProSEAL® Carrier Board 1. Refer to the instruction sheet packed
Maintenance & Cleaning 29 English 7 MAINTENANCE & CLEANING Cleaning of the Machine The equipment must be disconnected from the mains before
30 Troubleshooting 8 TROUBLESHOOTING List of common problems and solutions that the user can correct: Problem cause solution The power LED does
Glossary of Terms 31 English 9 GLOSSARY OF TERMS Decal An image that has been laminated on top (either heat-activated or pressure-sensitive) with a
32 Limited Warranty 10 LIMITED WARRANTY SEAL Graphics warrant to the original consumer purchaser that all new Seal® laminators that prove defectiv
Index 33 English 11 INDEX A Application Processes ...17 B Board Thickness ...5 C Cleaning...
2 Introduction INTRODUCTION We would like to thank you for purchasing a Seal 44/62 Ultra Plus, designed to give you many years of reliable service.
Table of Contents 3 English TABLE OF CONTENTS Introduction 2 Table of Contents 3 1 Specifications 5 1.1 Technical Specifications 5 1.2 Elect
4 Table of Contents 6 Application Processes 17 6.1 Loading the machine 17 6.1.1 Loading film onto a machine equipped with the interlock bracket.
Specifications 5 English 1 SPECIFICATIONS 1.1 Technical Specifications Imperial Metric Max. Working Width processes up to 50°C 44 Ultra Pl
6 Specifications BS 1363 – 13A wall receptacle: Use the provided BS 1363 plug France Belgium 1.2 Electrical specifications Push the power button (a
Safety / Important Safeguards 7 English 2 SAFETY / IMPORTANT SAFEGUARDS 2.1 Safety symbols used on the equipment. ROTATING PARTS MECHANICAL HAZARD
Comments to this Manuals